Dicor Camper Rubber Roof Replacement -BriteTek -35' x 8'6"
Dicor's BriteTek RV Rubber Roof Replacement membrane (35'x 8' 6")
combines the benefits of EPDM and TPO (thermoplastic olefin) and
provides a watertight roof with superior puncture and tear
resistance, making it ideal for OEM and aftermarket applications.
BriteTEK camper rubber roof membrane (35' x 8' 6") passes the ASTM
20-year accelerated aging test and resists
uneven weathering and fading. Manufacturers, service centers and RVers
find the Dicor RV rubber roof membrane easy to install and maintain. Requires Dicor adhesive, butyl tape and lap sealant or installation kit (38-1489).
The stiffer nature of TPO means it stretches less and is more
manageable, making installation quicker and easier. And BriteTEK camper rubber roof membrane is
available with or without fleece backing to match the needs of RV
Whether your Dicor BriteTEK camper rubber roof membrane (35' x 8' 6") is installed on a new recreational vehicle by
the manufacturer or installed on an older vehicle by your local dealer,
with the proper care you can expect years of superior performance.
Dicor's BriteTEK RV rubber roofing membranes are manufactured using polymers providing
unmatched protection against the elements and ultraviolet rays. In
addition, BriteTEK camper rubber roof membrane (35" x 8' 6") require less maintenance
than metal roofs, are energy efficient, will not rust, oxidize or
corrode and are quieter than metal roofs.
Dicor's BriteTEK RV rubber roof membrane (35' x 8' 6") is a product of Carlisle Syntec Incorporated, a leader in
commercial roofing materials. Designed specifically for the RV industry,
Carlisle membranes are the first choice of RV manufacturers. They have
received the Energy Star rating for environmental efficiency and are backed by the industry’s only 12-year warranty. That’s added peace of mind!
Dicor RV Rubber Roof Replacement Membrane Brite-Tek Available Sizes
BRITETEK RV Rubber Roof Membrane (35'x 8' 6") RETRO-FIT INSTALLATION GUIDE
The instructions contained herein are guidelines for installing
BriteTEK EPDM camper rubber roof membrane (35' x 8' 6") on older RV’s. When applied using the
proper techniques, materials, and tools, the Dicor BriteTEK RV rubber roof (35' x 8' 6") should
provide years of dependable, trouble free performance. To ensure proper
warranty coverage, you should adhere to the installation techniques and
materials described in this installation guide. Use of other procedures
and products may jeopardize your warranty coverage.
Note: Read fully and understand the procedures before beginning installation.
1. Tools and Materials:
A. Waterbased adhesive (901-BA) is applied to a wood substrate with a
roller. The BriteTEK camper rubber roof membrane (35' x 8' 6") is applied while the adhesive is still wet.
B. Butyl tape (BT-1834) must be under all vents and accessories on the
roof and termination moldings that contact the EPDM roofing. Butyl tape
should also be used under the EPDM membrane where it comes in contact
with the unit body at the front, rear, and side terminations.
C. Lap sealant (501-LS) is a self-leveling caulk used to seal
screw-type fasteners and termination moldings, formulated especially for
BriteTEK EPDM RV rubber roof membrane (35' x 8' 6").
D. Paint roller (not supplied) should be 9” wide short nap type. Used to apply waterbased adhesive (901-BA).
E. Push broom or squeegee (not supplied) used to remove air pockets and
ensure that the EPDM membrane is completely in contact with the
F. Caulking gun (not supplied) used to apply lap sealant (501-LS).
G. Roof decking (substrate, not supplied), depending on the roof load
requirements, should be at least 1/8” luan plywood. If the load
requirements are heavy (storage pods or consistent traffic) a minimum of
1/2” plywood is recommended. In most new unit applications, 1/4” luan
or plywood is the minimum material used, while 3/8” material is more
NOTE: Dicor does not warrant selection of substrate material. Feel free to contact Dicor with any questions.
2. Cleaning Information:
You will notice a powdery, white talc on the surface of your Dicor BriteTEK
EPDM RV rubber roof membrane (35' x 8' 6"). This talc is used in the manufacturing process of
the membrane. While this talc will not interfere with the performance of
your BriteTEK camper rubber roof (35' x 8' 6") and it will eventually be removed by the natural
elements, it is recommended that you clean the membrane within a week
BriteTEK EPDM RV rubber roof membrane (35' x 8' 6") can be cleaned with Dicor camper Rubber Roof Cleaner.
For stubborn stains, products containing mineral spirits are
recommended. Do not use Acetone or Citrus Cleaners.
Do not let any cleaning solvent come in contact with the membrane for
extended periods of time. Because dust and dirt may collect on the roof,
regular cleaning with Dicor’s RP-RC160C or RP-RC320S Rubber Roof
Cleaner is recommended. Do not park vehicle for extended periods where
roof will be exposed to tree sap or fruit as staining may result. A soft
bristle brush may be used during cleaning.
1. Remove all appliances, vents, moldings, etc. that may inhibit the current roofing material from being removed.
2. Evaluate the old roof. Dicor's BriteTEK camper rubber roof (35' x 8' 6") must have a sturdy
foundation. Determine if the entire roof should be removed, or if the
addition of decking (substrate) will be sufficient. Remember that the
substrate must be securely fastened on all edges and seams.
3. Either remove the old roof or apply the substrate over the old roof, if removal will create structural damage.
4. When applying the substrate, make sure it extends to the edges of
the roof. Also, make sure all seams are tight and as level as possible.
The substrate should be applied using screw-type fasteners with screw
heads level or slightly below the surface of the substrate. All
substrate seams should be on a rafter for necessary support and to
reduce the possibility of “seam separation”. If seams are wider than
1/16” you may want to bridge seams with Dicor Fleece Tape 511FT.
Additionally, if on the roof edge, the membrane will be going over a
sharp edge, you should either bevel the edge of the substrate with a
sander or place the Dicor Fleece Tape 511FT over the edge to protect the
membrane from the edge.
5. Route-out or cut all vent and appliance openings.
6. Broom or blow-off of substrate all foreign materials and check
entire roof for exposed screw heads or sharp objects that may
prematurely wear the BRITEPLY roof.
1. Locate the ends (front and rear) where the Dicor BriteTEK RV rubber roof will be
terminated. Use a chalk-line to mark these areas. Make sure there is
sufficient roof structure to fasten to.
2. Cover the roof with the Dicor BriteTEK camper rubber roof membrane (35' x 8' 6") making sure there is
sufficient length at both the front and rear termination points. Fold
membrane in-half, exposing the roof areas.
3. Open the waterbased adhesive (901-BA) and stir thoroughly. Using a
9” wide short nap paint roller, apply adhesive to the substrate at a
rate of 160 sq. ft. per gallon. The membrane is to be mated with the
adhesive as quickly as possible.
4. Fold the membrane the opposite direction and repeat step #3.
5. With the membrane in place, adjust to make sure there is sufficient
length at both termination points and on both sides of the vehicle.
Remove wrinkles by lifting and pulling the membrane. Do not stretch the
Dicor RV rubber roof membrane (35' x 8' 6").
6. Lightly squeegee or broom to eliminate air pockets, making sure the
camper rubber roof membrane (35' x 8' 6") is completely in contact with
7. Apply butyl tape (BT-1834) to the side of the roof edge molding.
While holding the molding, draw surplus material tight with a downward
pull. (You may staple the membrane in-place spacing 1/2” staples 3-5”
apart to keep proper tension.) For best results, install this molding
from the center of the vehicle toward the ends. When complete, use a
utility knife to cut surplus material from below the molding. Repeat on
NOTE: It may helpful to strike a chalk line to assist in keeping the side-body molding straight and in proper position.
8. Apply butyl tape (BT-1834) to the termination molding. On the front,
the front cap should lay on top of the membrane. Using a screw-type
fastener, install the termination moldings - making sure there is
sufficient roof structure. On the rear of the vehicle, the membrane
should lay on top of the rear cap.
NOTE: Butyl tape should also be used under the EPDM membrane where it
comes in contact with the unit body at the front, rear, and side
terminations. See all termination drawings for correct butyl placement.
9. Using a utility knife “X” cut all roof openings. Make sure all
openings are cut the same size as previous openings. Round all 90 degree
cuts to eliminate “running cuts”. Surplus material should be stapled
inside vent openings. Do not stretch the rubber membrane. Trim all
10. Apply butyl tape (BT-1834) to all appliances, vents, etc.
Re-install using screw-type fasteners. When installing the vents,
appliances, etc. you may notice that the BriteTEK camper rubber roof membrane (35' x 8' 6") near the
screws begins to “creep” and small air pockets form. Simply “walk” the
bubble toward the opening and hold-in-place while installing screw-type
Caulk all screw heads, front and rear termination bar and all accessories.
Note: Only Butyl Tape can be used with Brite-Ply membrane to assure proper seal.
11. Install lap sealant (501-LS) using a 1/4” to 3/8” bead, as follows:
A. Bridging the membrane on all appliances.
B. Both ends of the front and rear termination molding.
C. Top edge of side roof edge molding.
D. All screw heads located on the roof.
NOTE: Do not use silicone - it will not adhere to the EPDM rubber.
12. Clean all surplus caulk and debris from the roof.
NOTE: If the unit has a fiberglass or metal side
radius cap, a bonding adhesive may be used in these areas. Normally,
pulling the membrane tight under the side edge roof molding will be
sufficient. If you determine a bonding adhesive is necessary, please
call Dicor for additional information.
Dicor Camper Rubber Roof Replacement -BriteTek -35' x 8'6"